DC Controller
UPC4 Master
User Manual
Page 47/100
©2010. ELTEK VALERE DEUTSCHLAND GmbH. UM_UPC4_V2.00_E_R1.1_2011-01-04
Digital inputs* (section 6.7.1) Inversion and/or time delay of digital inputs DIB (*DIB is required)
Signals enable (section 6.7.2) Configuration of events, LEDs, and relays
Signals Sw mode (section 6.7.3) inverting/delaying of output signals
LVD/PLD/Drop diode (section 6.8)
LVD/PLD/Drop d. Setting of LVD/PLD & drop diode functions
Remotedisplay (section 6.9)
RD/RDP Remote Settings for "Remote Door Display" (RDD) and extended settings for „Remote
Display Panel“ (RDP*) respectively (*RDP enabled is required)
Additional functions (section 6.10)
Service/Enable (section 6.4.4) The services/functions which are enabled in the section "Service/Enable" can
be configured as described in the following:
Battery Test* (section 6.10.1) The switch off conditions of a running battery test can be configured as well
as the start date of an automatic battery test (requires the enabled service
"battery test").
Equalize charge* (section 6.10.2) The start and switch off conditions of an equalize charge can be configured
(* requires the enabled service "equalize charge").
Boost charge* (section 6.10.3) The start conditions of automatic boost charge and the conditions of "follow
up charge" (follow up charge time, voltage threshold) can be configured
(*requires the enabled service "boost charge").
Capacity Calc* (section 6.10.4) The capacity calculator can be configured. It calculates the expected battery
capacity (only of lead acid batteries).
(*requires the enabled capacity calculator)
SNMP* (section 6.10.5) SNMP settings (*SNMP enabled required)
Modem* (section 6.10.6) Modem configuration (*modem enabled is required)
Field bus* (section 6.10.7) ModBus/ ProfiBus configurations (*field bus enabled is required)
Mains monitoring (section 6.10.8) Configuration of external mains monitoring units or MMB board*
(*MMB enabled is required)
Hand-op. charge* (section 6.10.9) Manual charge of the batteries (*Hand-op. charge enabled is required)
System test* (section 6.10.10) Manual control of the rectifiers to test the system
(*System test enabled is required)
REMARK: Texts have no direct effect to system functions.
UPC4 Text (section 6.11)
Installation (section 6.11.1) Location, service no., contact person, etc.
Text Syst param (section 6.11.2) Display text for system measuring values
Text Battery* (section 6.11.3) Display text e for battery measuring values (*battery enabled is required)
Text Batt ident (section 6.11.4) Text of the used battery
Text Digital inp* (section 6.11.5) Text for digital inputs of the UPC4. Appears e.g. in the failure list
(* DIB enabled is required)
Text Relay outp (section 6.11.6) Text for relay output of the UPC4. Only for the display.
Text Fuses* (section 6.11.7) Text for the monitorable fuses (* FMB enabled is required)
Texte Gen. param. (section 6.11.8) Display text for general measuring values
Module ID-text (section 6.11.9) Text of the CAN modules are read out.
Module ID text EV (section 6.11.10 Text of the CAN modules are read out.
(192 paginas)
(78 paginas)
(80 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales